Secondly, can I use modified thinset with Kerdi? Modified thinset mortars aren't recommended for use with Kerdi because they must dry out to gain strength, whereas the membrane inhibits drying, which can lead to unpredictable results. For example, if a shower is used before the mortar has cured properly, leaks and polymer leaching can occur. Unmodified thinset is a blend of portland cement that's mixed with sand silica , and water retention additives, usually lime.
Water is then added to the blend to create the final mortar. Unmodified thinset is also known as dry set mortar. This type of thinset mortar is best for ceramic or natural stone installations. It's important to note that latex- modified thinset can still be used between the membrane and the subfloor because it is not impervious.
However, unmodified thinset should be used between the membrane and the tile. Asked by: Aboudou Milia asked in category: General Last Updated: 7th May, What's the difference between modified and unmodified thinset mortar? Unmodified thinset has been around forever. Unlike unmodified mortar , which consists only of a blend of Portland cement, sand, and water retention agents, modified thinset includes additional retention products, such as latex polymers, which can increase its performance and strength.
What is modified and unmodified thinset? Unlike unmodified mortar, which consists only of a blend of Portland cement, sand, and water retention agents, modified thinset includes additional retention products, such as latex polymers, which can increase its performance and strength. Can I use thinset over redguard?
You''ll be fine with thinset over Redguard on walls. It's recommended for waterproofing niches, shelves, and entire shower walls when tar paper or poly are not used as a vapor barrier behind the CBU. Is unmodified thinset waterproof? All portland based cementious products will allow water to pass through. It need to evaporate for the thinset to dry completely, extending the drying time greatly. The only place for the water in the thinset to escape is the grout lines at the edges of the tiles.
So this is where unmodified thinset has an advantage, trapped moisture in this case becomes a benefit. In unmodified thinset moisture that is not consumed by the hydration process will not impede the hardening of the thinset and will eventually escape. The damp cure that the impervious sandwich creates only makes the thinset stronger and promotes a very tenacious bond to the tile.
What type of thinset should be used for tile, modified or unmodified? It first depends on what kind of tiles you are going to be installing and on what kind of surface, you will determine which product you are going to use. Always go with what the tile manufacturer recommends. Modified thinset, there is cement, there are some other additives which help reduce the drying time, so that the cement where the thinsest stays moist, so it can cure rather than dry out.
Modified thinset would have. And so it's recommended that if you're putting tile down directly on to plywood then you would need to use a modified so that the plywood doesn't suck the moisture out of the thinset and it doesn't cure correctly. Depending on the kind of tile that you're putting down, if you're putting down large tile you also want to have that thin set to cure in a slower rate rather than using an unmodified type of a thin set on the bags, that'll tell you whether you need to just use water or if you need to add a polymer additive so you know depending on what you're putting down.
So if you're doing cement board again because it is on plywood you want to have it modified, so this is going to modify it and plywood. It's recommended for waterproofing niches, shelves, and entire shower walls when tar paper or poly are not used as a vapor barrier behind the CBU. Dry-Set Mortars. Portland cement-based unmodified thin-set mortars are dependent on the presence of moisture for hydration in order to gain strength.
Thinset mortar is an adhesive and binds the tile to the subfloor beneath. Grout is a filler used in the joints or gaps between the tiles. The products aren't interchangeable. Using mortar as grout to fill in the cracks could cause problems for your floor over time. Thinset is the wet base that you first trowel on the plywood to make the tile stick.
Higher latex content is essential for bonding to plywood. A quality unmodified thinset should be used and mixed with a latex additive. One example would be to use Laticrete's thinset mixed with Laticrete liquid latex additive. The humidity, temperature and air flow in a room affect how long it takes to dry , but thinset generally is cured and ready to walk on or grout in 24 to 48 hours.
Unmodified thin-set mortar is recommended to set ceramic and stone tile, including large format tiles, over the KERDI membrane. In the worst case, it's OK to cut the Kerdi , remove the damaged section, scrape up the thinset from the areas, and set a new piece of Kerdi.
A pain, yes, but the installation won't suffer performance-wise. Only took 45 minutes or so to remove the 9 tiles. Epoxy Tile Mortar It is impervious to water, so it does not need any special latex additives, as does some thinset. Epoxy mortars work well for porcelain and ceramic , as well as for glass, stone, metal, mosaic, and pebbles. Porcelain Tile: Most thinset manufacturer's want you to use a modified mortar for porcelain tile. Porcelain tile is near impervious and can be difficult for the mortars to grab a hold of which is the reason for the modified mortars.
They grab better. Thinset also called thinset mortar, thinset cement, dryset mortar, or drybond mortar is an adhesive mortar made of cement, fine sand and a water retaining agent such as an alkyl derivative of cellulose.
0コメント